Disconnect the wire from the spark plug and keep it away from the plug to prevent someone from accidentally starting the engine. Remove an obstruction from the discharge chute; refer to Clearing a Clogged Discharge Chute. Use the snow-cleanout tool Figure 14 , not your hands, to remove an obstruction from the discharge chute. Keep your face, hands, feet, and any other part of your body or clothing away from concealed, moving, or rotating parts. The impeller can throw stones, toys, and other foreign objects and cause serious personal injury to you or bystanders.
If the front of the machine rides up, shift the machine into a lower gear. If the front continues to ride up, lift up on the handles. Never store the machine with fuel in the fuel tank inside a building where ignition sources are present, such as hot water heaters, space heaters, or clothes dryers.
Allow the engine to cool before storing in any enclosure. When storing the machine for more than 30 days, refer to Before storage for important details. In snowy and cold conditions, some controls and moving parts may freeze. Do not use excessive force when trying to operate frozen controls. If you have difficulty operating any control or part, start the engine and let it run for a few minutes. After using the machine, let the engine run for a few minutes to prevent moving parts from freezing.
Rotate the Quick Stick to prevent it from freezing. Shut off the engine, wait for all moving parts to stop, and remove all ice and snow from the machine. With the engine off, pull the recoil-start handle several times and push the electric-start button once to prevent the recoil starter and electric starter from freezing up. Important: You can find more information about maintaining and servicing your machine at www. Before performing any maintenance, service, or adjustment, shut off the engine and remove the key.
If major repairs are ever needed, contact an Authorized Service Dealer. Check all fasteners at frequent intervals for proper tightness to ensure that the machine is in safe working condition. Disconnect the spark-plug wire. Refer to Replacing the Spark Plug.
Check the skids and the scraper to ensure that the auger does not contact the paved or gravel surface. Adjust the skids and the scraper as needed to compensate for wear. Check the tire pressure; refer to Checking the Tire Pressure. Loosen the nuts that secure both skids to the auger sides until the skids slide up and down easily. Note: If the pavement is cracked, rough, or uneven, adjust the skids to raise the scraper. For gravel surfaces, adjust the skids further down to prevent the machine from picking up rocks.
Note: If the skids become excessively worn, you can turn them over and set the unused side toward the pavement. If the machine does not drive in the forward or reverse speeds or it drives when you release the traction lever, adjust the traction cable. Engage the traction lever and hold it in place Figure Loosen or tighten the turnbuckle to adjust the spring length to 5.
Tighten the jam nut Figure 32 , ensuring there is slight tension on the cable. If the traction cable is properly adjusted but a problem remains, contact an Authorized Service Dealer. Tighten the jam nut Figure 34 , ensuring that there is slight tension on the cable.
Clean the area around the pipe plug Figure Check the oil level in the gearbox. The oil should be 9. If possible, run the engine for a few minutes before changing the oil because warm oil flows better and carries more contaminants.
Use Figure 36 below to select the best oil viscosity for the outdoor temperature range expected:. Clean the area around the oil-drain cap Figure Lightly lubricate the hex shaft yearly with automotive engine oil Figure Important: Do not get oil on the rubber wheel or the steel friction pulley because the traction drive will slip Figure Set the gap between the electrodes on a new spark plug at 0.
Note: Ensure that the ignition wire snaps completely into place on the spark plug. If the discharge chute does not lock into the desired position or does not unlock so that you can move it to another position, adjust the discharge-chute latch. On the last refueling of the year, add fuel stabilizer to fresh fuel as directed by the fuel stabilizer manufacturer. Important: Do not store fuel longer than that suggested by the fuel-stabilizer manufacturer. Allow the engine to run until it shuts off.
When you can no longer start the engine, it is sufficiently dry. Touch up chipped surfaces with paint available from an Authorized Service Dealer. Sand affected areas before painting, and use a rust preventative to prevent the metal parts from rusting.
Perform the annual maintenance procedures as given in the Recommended Maintenance Schedule; refer to Before storage. Toggle navigation. Figure 1 Model and serial number location. Figure 2 Safety-alert symbol. Figure 3. General Safety. Do not put your hands or feet near moving components on the machine. Keep clear of any discharge opening. Keep bystanders a safe distance away from the machine. Keep children out of the operating area.
Never allow children to operate the machine. Shut off the engine before unclogging, servicing, or fueling the machine. Safety and Instructional Decals. Prime the engine 3 times. Engage the choke. Pull the starter cord. Once the engine is running, disengage the choke. Thrown object hazard—keep bystanders a safe distance away from the machine. Installing the Upper Handle. Figure 4. Installing the Chute. Figure 5. Installing the Traction-Control Linkage. Figure 6. Installing the Chute-Control Rod.
Figure 7. Installing the Snow-Cleanout Tool. Figure 8. Checking the Engine-Oil Level. Checking the Tire Pressure. Figure 9. Checking the Skids and Scraper. Checking the Operation of the Traction Drive. Carefully check the traction drive and adjust it properly, if necessary.
Keep clear of any discharge opening. Keep bystanders, especially small children, out of the operating area. Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. Refer to Checking and Adjusting the Control Cable. A selection of Toro approved attachments and accessories is available for use with the machine to enhance and expand its capabilities.
Contact your Authorized Service Dealer or authorized Toro distributor or go to www. To ensure optimum performance and continued safety certification of the machine, use only genuine Toro replacement parts and accessories.
Replacement parts and accessories made by other manufacturers could be dangerous, and such use could void the product warranty. Note: Determine the left and right sides of the machine from the normal operating position. For electric-start models only: Use extension cords and receptacles as specified in the manual. Inspect the electrical cord before plugging it into a power source.
If the cord is damaged, replace it. Unplug the power cord whenever you are not starting the machine. Wear appropriate clothing, including eye protection; long pants; substantial, slip-resistant footwear; and hearing protection. Tie back long hair, secure loose clothing, and do not wear loose jewelry. Thoroughly inspect the area where you will use the machine, and remove all doormats, sleds, boards, wires, and other foreign objects. If a shield, safety device, or decal is damaged, illegible, or missing, repair or replace it before beginning operation.
Also, tighten any loose fasteners. Fuel is extremely flammable and explosive. A fire or explosion from fuel can burn you and others. Fill the fuel tank outdoors when the engine is cold. Replace the fuel cap securely and wipe up spills. Fill the fuel tank as shown in Figure 12 ; do not fill above the bottom of the fuel tank neck. Important: For best results, purchase only the quantity of fuel that you expect to use in 30 days. Shut off the engine before unclogging the machine and always use a stick or the snow-cleanout tool if provided.
Stay behind the handles and away from the discharge opening while operating the machine. Keep your face, hands, feet, and any other part of your body or clothing away from moving or rotating parts.
Use your full attention while operating the machine. Do not engage in any activity that causes distractions; otherwise, injury or property damage may occur. Exercise caution to avoid slipping or falling, especially when operating the machine in reverse. Exercise extreme caution when operating the machine on walks or roads. Stay alert for hidden hazards or traffic. Never attempt to make any adjustments while the engine is running, except as directed in the instructions.
After striking a foreign object, shut off the engine, remove the key, and inspect the machine for damage. Repair any damage before starting the machine.
If the machine starts to vibrate abnormally, shut off the engine and check immediately for the cause. Shut off the engine whenever you leave the operating position, before clearing or unclogging the collector, rotor, or discharge chute, and when making any repairs, adjustments, or inspections. Note: Remove your glove when you push in the primer so that air cannot escape from the primer hole.
Important: Do not use the primer or the choke if the engine has been running and is hot. Excessive priming may flood the engine and prevent it from starting.
To use the electric starter electric-start models only , connect a power cord to the electric-start plug-in first and then to a ground fault circuit interrupter GFCI power outlet.
Use only a UL-listed, gauge power cord recommended for outdoor use that is not longer than 15 m 50 ft. Thoroughly inspect the electrical cord before plugging it into a power source. If the cord is damaged, do not use it. Replace or repair the damaged cord immediately. Contact an Authorized Service Dealer for assistance. Important: Run the electric starter no more than 10 times at intervals of 5 seconds on, then 5 seconds off.
Running the electric starter extensively can overheat and damage it. If the engine does not start after this series of attempts, wait at least 40 minutes to allow the starter to cool before attempting to start it again. If the engine does not start after the second series of attempts, take the machine to an Authorized Service Dealer for service. If you leave the machine plugged into a power source, someone can inadvertently start the machine and injure people or damage property electric-start models only.
To engage the rotor blades, hold the control bar against the handle Figure To disengage the rotor blades, release the control bar Figure To raise or lower the angle of the chute deflector, press the trigger on the chute deflector and move the chute deflector up or down. Moving the control down the handle rotates the discharge chute to the left; moving the control up the handle rotates the discharge chute to the right Figure To raise or lower the angle of the chute deflector, press the trigger on the chute deflector and move the chute deflector up or down Figure The rotor blades can throw stones, toys, and other foreign objects and cause serious personal injury to you or bystanders.
If the machine does not propel itself forward on slippery surfaces or in heavy snow, push forward on the handle, but allow the machine to work at its own pace. The machine may leave rubber marks on new brushed or light-colored concrete. Test on an inconspicuous location before use.
These marks are not permanent. Never store the machine with fuel in the fuel tank inside a building where ignition sources are present, such as hot water heaters, space heaters, or clothes dryers.
Allow the engine to cool before storing the machine in any enclosure. When storing the machine for more than 30 days, refer to Before storage for important information. Run the machine a few minutes after throwing snow to prevent freeze-up of the collector and rotor.
Let the engine run for a few minutes to prevent moving parts from freezing. Shut off the engine, wait for all moving parts to stop, and remove ice and snow from the machine. In snowy and cold conditions, some controls and moving parts may freeze. Do not use excessive force when trying to operate frozen controls.
If you have difficulty operating any control or part, start the engine and let it run for a few minutes. Check the oil level in the gearbox.
The oil should be 9. If possible, run the engine for a few minutes before changing the oil because warm oil flows better and carries more contaminants. Use Figure 37 below to select the best oil viscosity for the outdoor temperature range expected:.
Clean the area around the oil-drain cap Figure Lightly lubricate the hex shaft yearly with automotive engine oil Figure Important: Do not get oil on the rubber wheel or the steel friction pulley because the traction drive will slip Figure Set the gap between the electrodes on a new spark plug at 0. Note: Ensure that the ignition wire snaps completely into place on the spark plug.
If the discharge chute does not lock into the desired position or does not unlock so that you can move it to another position, adjust the discharge-chute latch. Use a Toro light bulb or equivalent GE 37W halogen bulb. Do not touch the bulb with your hands or allow dirt or moisture to come into contact with the bulb. Remove the wire connector from the back of the headlight Figure Turn the base of the bulb counterclockwise until it stops Figure Remove the bulb straight out from the back of the headlight Figure Insert a new bulb into the back of the headlight Figure Turn the base of the bulb clockwise until it is snug Figure Insert the wire connector straight into the back of the headlight until it is securely in place Figure On the last refueling of the year, add fuel stabilizer to fresh fuel as directed by the fuel stabilizer manufacturer.
Important: Do not store fuel longer than that suggested by the fuel stabilizer manufacturer. Allow the engine to run until it shuts off. When you can no longer start the engine, it is sufficiently dry. Touch up chipped surfaces with paint available from an Authorized Service Dealer. Sand affected areas before painting, and use a rust preventative to prevent the metal parts from rusting.
Perform the annual maintenance procedures as given in the Recommended Maintenance Schedule; refer to. Toggle navigation. Figure 1 Model and serial number location. Figure 2 Safety-alert symbol. Figure 3. General Safety. Do not put your hands or feet near moving components on the machine.
Keep clear of any discharge opening. Keep bystanders a safe distance away from the machine. Keep children out of the operating area. Never allow children to operate the machine. Shut off the engine before unclogging, servicing, or fueling the machine. You can find additional safety information where needed throughout this manual.
Safety and Instructional Decals. Prime the engine 3 times. Engage the choke. Pull the starter cord. Once the engine is running, disengage the choke. Thrown object hazard—keep bystanders a safe distance away from the machine. Installing the Upper Handle. Figure 4. Installing the Chute. Figure 5. Installing the Traction-Control Linkage. Figure 6. Installing the Chute-Control Rod.
Figure 7. Connecting the Headlight Wire. Figure 8. Installing the Snow-Cleanout Tool. Figure 9. Checking the Engine-Oil Level. Checking the Tire Pressure.
Figure Checking the Skids and Scraper. Checking the Operation of the Traction Drive. Carefully check the traction drive and adjust it properly, if necessary. Product Overview. Figure 14 Snow-cleanout tool attached to the handle. Before Operation. Before Operation Safety. Fill the tank outdoors when the engine is cold.
Wipe up spills. Do not handle fuel when smoking or around an open flame or sparks. Store fuel in an approved fuel container, out of the reach of children.
Filling the Fuel Tank. Do not use gasoline containing methanol. Do not add oil to gasoline. During Operation.
During Operation Safety. Never direct the discharge toward people or areas where property damage can occur. Exercise extreme caution when operating on slopes. Never operate the machine without good visibility or light. Do not operate the machine while ill, tired, or under the influence of alcohol or drugs. Look behind and use care when backing up with the machine.
When not actively clearing snow, disengage power to the auger. Never attempt to make any adjustments while the engine is running. If the machine should start to vibrate abnormally, shut off the engine and check for the cause. Do not overload the machine capacity by attempting to clear snow at too fast a rate. Never touch a hot engine or muffler. Starting the Engine. Figure 17 Ignition key. Figure 21 Electric-starter button Electric starter plug-in Recoil-start handle.
The electrical cord can become damaged, causing a shock or fire. Exercise extreme caution when operating on slopes. Never operate the machine without good visibility or light.
Do not operate the machine while ill, tired, or under the influence of alcohol or drugs. Look behind and use care when backing up with the machine. When not actively clearing snow, disengage power to the auger. Never attempt to make any adjustments while the engine is running. If the machine should start to vibrate abnormally, shut off the engine and check for the cause. Do not overload the machine capacity by attempting to clear snow at too fast a rate.
Never touch a hot engine or muffler. Starting the Engine. Figure Figure 11 Choke lever. Figure 12 Symbols on the choke lever indicating to pull out the choke lever to activate the choke. The electrical cord can become damaged, causing a shock or fire.
Engaging the Rotor Blades. Disengaging the Rotor Blades. Shutting Off the Engine. Adjusting the Discharge Chute and Chute Deflector. Figure 19 Chute handle Chute-deflector handle. Clearing a Clogged Discharge Chute. To clear the chute: Shut the engine off! Wait 10 seconds to ensure that the rotor blades have stopped rotating.
Always use a clean-out tool; never use your hands. Operating Tips. Keep the area to be cleared free of all objects that the rotor blades could pick up and throw.
Keep all children and pets away from the area of operation. After Operation. After Operation Safety. Preventing Freeze-up after Use. Clean off any snow and ice from the base of the chute.
Rotate the discharge chute left and right to free it from any ice buildup. Recommended Maintenance Schedule s. Maintenance Service Interval Maintenance Procedure After the first hour Check the control cable and adjust it if necessary.
Check for loose fasteners and tighten them if necessary. After the first 2 hours Change the engine oil. Before each use or daily Check the engine-oil level and add oil if necessary. Yearly Check the control cable and adjust it if necessary. Inspect the rotor blades and have an Authorized Service Dealer replace the rotor blades and scraper if necessary. Change the engine oil. Service the spark plug and replace it if necessary. Have an Authorized Service Dealer inspect the drive belt and replace it if necessary.
Yearly or before storage Prepare the machine for storage. Maintenance Safety. Read the following safety precautions before performing any maintenance on the machine: Before performing any maintenance, service, or adjustment, shut off the engine and remove the key.
Do not change the governor settings on the engine. Purchase only genuine Toro replacement parts and accessories. Checking the Control Cable.
Figure 21 Adjuster link Z-fitting Spring cover Unhook the spring here. Figure 22 Upper end of spring Insert the upper end of spring into this hole Pivot point Remove the upper end of spring from this hole. Inspecting the Rotor Blades.
Maintenance Service Interval Maintenance Procedure Yearly Inspect the rotor blades and have an Authorized Service Dealer replace the rotor blades and scraper if necessary. Figure 23 The wear-indicator hole is intact; you do not need to replace the rotor blades. The wear-indicator hole is exposed; replace the rotor blades and scraper. Changing the Engine Oil. Yearly Change the engine oil. Figure 25 Oil-fill cap. Servicing the Spark Plug.
Figure 29 Screw 4 Shroud Spark plug Spark-plug wire. Figure 30 Center-electrode insulator Side electrode Air gap not to scale. Figure 31 Breather tube Carburetor drain bolt. Replacing the Drive Belt.
Figure 33 Brake spring install on idler arm here Idler pulley Engine pulley Rotor pulley. Storing the Machine. Please read the following safety information and scroll down to close. By closing this safety section, I acknowledge that I have read and understood it.
0コメント